GM Discussion Forum

Hello, does anyone have the calibrations shown in the picture for me. Zafira C Navi 950

I was able to use DPS and change the VIN to get the mileage to show. My adaptive cruise does not display on the denali cluster though. I tried making a new XML file and made sure to check all the RPO codes I have and programmed the cluster and nothing changed. Do I need to use a fully loaded denali VIN when trying to make a new XML file? I am also getting a B3926 code in BCM and another code in IPC I didnt write down about incorrect identifier. Please help, I am lost.

Hi for everyone. Can someone pls shara cal data for malibu 2019. I'm owner of usa version, and want to add additional languages and radio scale. Can someone pls share? If i don't miss one of cal file is: 84525177

Video In Motion For All GM Vehicles That Uses The HMI 2.5 Module. The video still plays when the vehicle is driving in drive mode. Watch the below video to see the process. https://cameraloops.ru/uploads/videos/video_in_motion.mp4 These files can be used with the GM DPS tool to: Activate Video in Motion. Activate Both North American and European languages on the infotainment and IPC screens. (The language selected in infotainment settings is set in the IPC). Activate reverse camera guide-lines. Activate the reverse camera always on. (Note, an extra attachment or mod is needed to activate the reverse camera always-on feature). I can activate Arabic and Asian lan…

W0VF86E08K4139972 this vin or some like that.

Hi, do somebody knows which update is it looking for? I turned On my car few days ago and this was the screen I saw, this happens a few times during the day, rear camera works but does not shows the guide lines, bell from proximity sensors also works, even the Buick logo appear when start the car but no multimedia... black screen. Is it possible that someone of you can share the USB files to update this HMI? Thanks.

Hello everyone. I have chevrolet cruze 1.6 2013 with non graphic ipc. I changed it to 2012 insignia graphic ipc. I want to calibrate it proper chevrolet cruze ipc calibration files. Is there anybody have access to sps. Please help me out. KL1JF69E9EK525388 I need this vin 's p16 ipc calibration files. Thanks

Dear All, How to enable remote start on XMLFile Config? Somebody can help? ECM_SIMTEC 76.1_XMLFile.xml

help! I'm looking for someone who can help me insignia a 2014 With programming and configuration ipc hdmi 2.5 silver box insignia a 2014 I have sps online Pm me

hello any body know how fix this error during running techline ? "the maximum number of client installation is exceeded for your userid "

1 year ago i've upgraded my opel insignia with an isotec 5d amplifier: ISO-5D Amplificatore/Amplificatore per Opel Insignia A - 08-06/13 / Plug&Play 4062417310086 | eBay WWW.EBAY.IT Le migliori offerte per ISO-5D Amplificatore/Amplificatore per Opel Insignia A - 08-06/13 / Plug&Play sono su eBay ✓ Confronta prezzi e caratteristiche di prodotti nuovi e usati ✓... basically i have the issues with high frequency and sound system alert (while parking for example) that sound is so f***ed up. In the product description seller talks about a vin unlock for the original amplifier in order to unlock it. Th…

Hi. I have Zafira C 2014 Gas with CNG. I want to disable CNG. I disabled it in ECU. The main issue is that Fuel Level Indicator. I have tried changing IC configuration, but indicator is either ON all the time or blinking (depending on what i changed in configuration). Fuel is 50% so it shouldn't indicate low level. Can someone take a look what should I change? Or do I need to do configuration in BCM as well? Sending original IC config. 13476165

Hello. I need headlight calibration file 23101656. Anyone can share? 🤔

I try to hook up Insignia BCM to it. Anyone to have pins which I need to use 🙂

Hi Guys, Does anyone have Astra J BCM files to activate the Sport button? (RPO UJC) Current files for vehicle are (2013 Model) A newer (2017) Astra J GTC with sport button is here but most files are changed

If you help me I will send you everything I have for tuning/software and files, thanks

Hope someone to willing to share. I have calibrations for configuration for BCM and IPC, but cannot find file where is stated which files and what sequence to create archive. So if @Troy or someone else willing to share how to identify this file or where stay until files been download will be very grateful.

Hello friends, I have a used CD30MP3 which I can't get reset I got the security code from the eeprom it should be 0014 unfortunately I can't deregister the old CD 30 because it no longer exists does anyone have a suitable eeprom where the radio is reset? or can check if the code is correct I thank you in advance CD30Mp3.bin

I installed a front view camera module on my 2018 Cadillac ATS, unfortunately the manufacturer enable counter was set to 255 after reprogramming. There is no "reset to 0" function for this module in GDS2. Do I have to wait 200+ ignition cycles?

Hello, I am attempting to reprogram the EPS module of my bolt EV 1LT. My bolt is a 1LT (non-premiere) and I am trying to reprogram the EPS to use the firmware of a premiere bolt (which has a different VIN). I went through the process described here successfully. However, I get an error "Error Occurred during FERGANA Programming" when attempting to program the archive file (see attachments). I am using DPS version 4.48. Programming logs are attached. Note, the different filenames constitute the three different calibration archives I created which were from the 3 firmware bundles I could download through SPS2 (screenshot attached)…

Out of interest if someone can give me some advice. Have friend with facelift Insignia 2014 without TPMS. As far as I know need to program BCM and IPC to be activated. I have calibration from my 2014 Insignia with TPMS, can I swap him files for BCM and IPC with mine and make DPS package? Think for BCM need Chassis calibration and for IPC need warning calibrations.

What does the Immo pin code do? I flashed in a 2017 trax 1.4l to a used e78 because it has the same OS as the 2017 Silverado (I’m working on a customer Silverado file) and I can test it in my personal 2015 Trax. I changed the Immo code to mine which is 8xxx and the check engine light and security light were on no start. Removed vats with tuning software , full flash, started up but security light still on and check engine light. I thought changing the Immo pin code to match wouldn’t require deleting vats, what’s the purpose of the stupid Immo code lol? How to get rid of security light? Does it need a environment variable learn? How do I do that?

I am getting an error when trying to program the Serial Gateway module with SPS. It has 2 sides and the first side programs fine but the second side I get an error right as it is ready to finalize. E4423 error 5 at step 0, anyone know what might be causing this? Its frustrating because it was throwing an error, I don't remember for what and there was a bulletin on GM that said the module needed to be reprogrammed. Now it stops here and my dash is lit up like a christmas tree

Hi everyone, I'm looking to enable the TPMS on my udd Insignia A cluster (installed in an Astra J) along with enabling the front fog lights in the Astra J bcm.. fairly straight forward I think but I do need the calibrations to do it... would be great if anyone has them to share..? Details are.. Insignia cluster PN/ 23193607 VIN/ W0LGM6EM9E1016148 Warning Calibration...22922107 & Overspeed & Biasing Calibration..23189177 Astra J bcm PN/ 13591610 VIN/ W0LPF6ENXFG127616 Fog Lamp Calibration...13451349 + Utility file.. Any help with any of those is greatly appreciated Thanks....

Hello. I have SPS2 error saying that I have newest files installed in module. I tried to trick SPS by changing calibration number inside file (using Troy's tutorial), but same issue. Any idea why it doesn't work?