General Forum

Hello, citizens of Cameraloops. I hope you're doing great. I need your help, who knows how to find a programmer to read this chip ST. 4256BRP.

Hello guys I have been trying to buy Techline vin subscription but all my credit cards have been rejected Anybody could help to purchase?

Hi All It's anyone can help with calibration file to downloading from IPC please W0LGM8EL0B1073269 THANKS

Hello friend I have a big problem with my 2023 Chevy truck, my truck has been stolen and a few months later I managed to recover it, when my truck was stolen I sent an alert through OnStar to deactivate it, but now my truck does not work, I already spoke to the OnStar company and deactivate the alert but I still have an immobilizer message, I have even programmed 2 new keys with MDI2 OEM and I still have the same immobilizer problem, can you help me?

hello i need the following calibration files, does anyone have them? Thanks appreciate your help. VIN W0LGT8GX9D1141168

How can I verify , my pin was changed . Is there a command that will confirm pin entered is correct 😆. Thanks all and best regards

HAPPY TO SEE CAMERALOOPS IS BACK IN ACTION 🥰

Hello, someone can help me to get some calibration or configuration files for my cadillac ct6 UHS 12.3 full digital Instrument cluster? i messed up when i was trying to read the eeprom and now it shows only a blank page with the speeddometer. VIN: 1G6KP5R64JU115058

hello, can comeone help me with some calibration files for a 2019 onward IPC (white needles)?

Hi !Just wondering did someone manage to change VIN in those steering Racks succesfully . Thank you

i need change the vin from ebcm gmc terrain 2018 any one have solution. thanks jorge costa

Hi, looking for calibration files for a 2010 buick enclave 5GALRCED2AJ127040

Good evening, I'm wondering if anyone could help changing bcm configuration to halogen from xenon on a 2011 vauxhall insignia. I believe cars with xenon have a headlight control module but halogen cars are controlled from bcm only,the wiring side I should be able to figure but the bcm configuration I could do with some help if possible. Thankyou liam.

Hello everyone, I'm looking to program a used PCM E86 I need a Virgin file for DPS or Flex, to be able to program it with SPS, or if it can be done by changing VIN and PIN I can go that way too thank you....

Hey everyone just wondering if anyone can help me out with Bcm and IPC files for W0LGT6EU9E1028075 Thanks appreciate your help.

I am wanting to swap a denali uplevel cluster from a 2014 denali truck to my 2015 silverado 1500. I have purchased the used cluster, its off a 2014 sierra 6.0 my truck is a 5.3 1500. From my understanding they will work as long as i can get it programmed correctly. I am wondering the process I need to take to change the vin and pin off the used cluster to make it work with my truck. Do i just plug the cluster into my truck and do a reprogram with sps?

Hello, has anyone tried adding other languages to HMI 2.5 Chevrolet Camaro? What does he need? Is there a guide somewhere on how to do this? As far as I know, all you need to do is change the region, but I don't know how true it is. Regards

Hello everyone, Maybe somebody can help me, I would like to retrofit TPMS in my Insignia 2014 which does not have tpms originally, I found the plug on the back behind the bumper and connected the module, check and power working after ignition on I have replaced the 8'' cluster, which has pressure monitoring, but shows only dashes, So now left BCM to activate, I tried SPS config / setup there is a question if I have TPMS, and the whole configuration process, but still nothing happens, will someone tell me exactly what to do, is this function in calibration? Thanks greetings

hi all if anyone have HMI 2.0 USB firmware - 23228506 for insignia 2015 PLEASE I was install USB firmware from 2014 - 23266029 its working but map no loading, I try go back to original one anyone can help please Thanks

hellos i need some help i have a chevy colorado 2020 and i need update the screen firmware can some one help me on it??

I have this friend who wants to program the Red Denali cluster (gas engine) from a Yukon to a 2016 Chevy Silverado 2500 Diesel. Is that possible?

Hello to all. I have a 2017 6.2 engine, 8l90 transmission and a 2018 Yukon digital screen cluster all going into a 2006 hummer. I have disable tons of the warnings in the cluster that are not going to be used. For instance i have disable the theft lock light and service theft warning that scrolls the cluster. Has anyone done anything similar? I have ABS, Traction control airbag light, service adaptive cruise and service safety restraint system left that I can't seem to find in the xml file. Any ideas?

Morning guys. Is there a problem if I use an old 2015 Yukon Denali red face cluster in a 2018 GMC Sierra? Like an incompatibility issue?

Hello everyone, had the tcm in my captiva fail, transmission is the 6t50. Was told by GM Holden that it will cost about $4500 to replace the tcm. brought a used gen1 tcm from ebay and figured id just re-program it through Techline Connect however i get a "E2700 hardware mismatch error" when trying too. i figure the part numbers are different and its locked to another car. Does anyone know how i can make this work, the original tcm is gone so i cant pull data from it. i have an MDI j2435 box and autel scanner. ive been searching all night but still at a loss. if i cant make it work i think i can buy a pre programmed tcm from aliexpress, where i send them my vehicle VIN. th…

Dose anyone Have calibrations for a 2013 Buick regal GS radio, RPO code Uhq & Up9. I changed the vin on the eprom chip and the radio works but the screen is black, is this a calibration issue? The radio came from a 2013-14 Buick encore. I Attempted to program via sps2 but got error code e9044 tool lock error. Thanks, Skyler