GM Discussion Forum

good morning, need help i change the radio,hmi,and display, and the cluster check all my fuses and relays still nothing, please help

Hello guys, my original HMI is 2.0 with part number 23266007, can i replaced with 2.5 HMI and can be programmed

hi everyone i have Chevrolet Suburban truck 2007 i am trying to replace 2 calibration in ecm package with same model year vehicle when i try to program its giving me Paddingerror i think op-code 53 compare data step in the end of programming its showing me successfully programmed but nothing changed inside the calibration i am attaching the log can someone please help me to solve the problem... thanks ecm_sun_ban_ap3.zip ProgramLog.ecmsuburban.Txt

Hello guys, i hope you are all good, is there a way of knowing my parts part number by my vin number. the car takes time of shipping to me and i want buy their modules before it delivers to me

Guys, I would like to disable suspension error message in ipc, because I have upgraded the stock magna ride suspension in a 2016 camaro. And now I have C0575-04 and C0575-0D error message in scm and suspension error message in ipc. It is enough if someone can advise me which calibration is responsible for those messages and I gonna try to remove. Second question is for the same car. I have replaced taillights and the load is too low. Now I have hyper flash in ipc. Please help me to disable that. I don't know where I have to do it. In bcm? In ipc? Or in both? Which calibration is responsible for those features? Regards, J…

Thank you for your help so far! With the help of a friend who is much smarter than me, I have made some progress the hard way. I was able to read and edit the eeprom to change the pin/vin. I installed the IPC and at first a few things were not working. 1. "Track" mode was missing from mode selections. 2. The crash alert on the wheel did nothing. 3. There was a message about Service AWD. I then logged in to SPS and performed a setup and config. That made some things work and others broken. 1. The AWD message was fixed 2. The crash detection alerts button was working on the wheel 3. Track mode was now back in the menu …

Hello all, I am wanting to swap out my base vsport cluster to the premium digital. What are the proper steps to do so with a used cluster from a 19 premium vsport. I assume we have to change the vin? Can it be done with sps, or dps? I would need to remove the HUD feature as my vehicle won't have that installed. Thank you for helping out if you can.

Hello, I am looking to hire someone to create a parameters/definitions file for HPTuners that allows me to set the allowable timing chain wear (differential between CKP and CMP) on a GM LY7/LLT engine before DTCs are set. GM Had a TSB for this issue where they issued an updated calibration on SPS that modified this very parameter, so it should be easy enough to get the original calibration, and the updated one from SPS and compare, use TunerPro to generate a custom definition for HPT. I am willing to hire someone to do this. Please let me know if anybody here could do something like this. -Thanks!

Hello all members. I am struggling with a 2015 Chevrolet traverse that had the transmission replaced with a used one. SPS2 won't let me program it. I created the SPS files for DPS, entered the current VIN of the vehicle, hit program but it ends up giving me a DPS error. Does anyone know if there is a method for this car? Thanks everyone.

Hi all i am trying to communicate Ipc on bench with connected BCM and i connected power ground wires of bcm and ipc and low speed canbus wire and i can get controller info of ipc but in few seconds ipc display blank and again wakeup i can get controller info sometimes and sometime communication error can someone please share the info how can i setup the ipc on bench for dps thank you all

Guys, please help me to get the calibration for EU IOT audio system VIN: W0VZX8GS1N1000900 Regards, Janos

hi all, is there a way to change the design of infotainment (not the IPC) in Insignia to Buick Regal Theme? thanks for a reply...

I need support with the update from 2014 to 2016 firmware so it then supports Android Auto / Car PLay tracklist display, skip backwards / forwards also more menu unlocks than the older 2014 firmware

Changing the mileage in GM vehicles is vital when recycling a used BCM module. Using the GM DPS software and this particular DPS type4 application file, you can achieve this. To display the Type4 tab option on DPS, you need to install GM Techline connect and run the SPS programming option or copy these two files, dllsecurity.dll and tisvcsv4.dll, to C:\Users\Your_UserName\sps\nativelibs, folder. CLICK HERE FOR THE .dll FILES. Watch this video for the process. https://cameraloops.ru/uploads/videos/change_mileage2.mp4 DPS Type4 mileage change file View full gm info

VIN change file for most 2-byte EBCM EBCM VIN Change For Cadillac Escalade 2018. 2-Byte Seed DPS Archive EBCM VIN Change For Corvette 2014. 5-Byte Seed DPS Archive View full gm info

What do I need to do to be able to reset a used BCM on a 2022 Onix Turbo?

Hi guys anyone gots the diagram of latch control of driver door and passenger door for c8 corvette

I need VIN# Chevrolet Cruze Year 2012-2014 have factory remote start on Key fod. Can someone share ? Thanks

Utility File Step=01 Opcode=01 Utility File Step=02 Opcode=1A 09:33:50.4<[.H..] 00 00 07 E0 1A C0 [0006] FramePad 09:33:50.4>[.H..] 00 00 07 E0 [0004] TxDone TxMsgType 09:33:50.4>[.H..] 00 00 07 E8 5A C0 00 C1 92 E8 [0010] Utility File Step=03 Opcode=27 09:33:50.4<[.H..] 00 00 07 E0 27 01 [0006] FramePad 09:33:50.4>[.H..] 00 00 07 E0 [0004] TxDone TxMsgType 09:33:50.4>[.H..] 00 00 07 E8 67 01 01 75 89 43 06 [0011] >> GM 5-byte Security: Algo 80, Chal 0175894306, Resp 0000000000 >> Status Invalid Prefix >> ReturnToNormalMode (0x20) service 09:33:50.5<[.H..] 00 00 01 01 FE 01 20 00 00 00 00 00 …

Does anyone have the Calibration files for Astra J OPC intelilink? or Even VXR? I only need the "Software module 8" which is the brand file. I have only managed to find the Standard Vauxhall and Chevrolet brand files on here. I have uploaded the standard Holden Cascada calibration files that i have to the downloads section. Thanks

Hello, please help me activate Astra J 2011 TPMS UJM in BCM Astra J GTC W0LPF2DC7CG055200.zip

Without a pin code change in a used IPC, BCM, EBCM, and SDM you won’t be able to program those modules via GM online SPS service using the vehicle’s original PIN. This DPS file can change the PIN CODE in most GM Global-A 5 bytes EBC ABS modules. Without a pin code change in a used IPC, BCM, EBCM, and SDM you won’t be able to program those modules via GM online SPS service using the vehicle’s original PIN. Important In order to change the PIN code in a used GM module, you will need to know the PIN code that’s already programmed/stored in that module. Without knowing that PIN code, you cannot change the PI…

DPS successfully flashes the block BCM, but the calibrations remain the same. Other blocks (IPC, Radio) are updated without problems. Anyone have any ideas? What am I doing wrong? I use DPS v4.52.2000 BCM_Programming_log.Txt BCM_Read_log.Txt

In 10 minutes read from eeprom 🤣🤣🤣 now left to be installed in car and see if all is set correctly

Hello everyone! I have a car with a diesel engine A20DTH with automatic transmission, to activate remote start, do I need to change the calibration files or do I need to change the XML file from the SPS2 folder Type4 cache for GM DPS? As I understand, I need to work with BCM and ECM units? Which lines need to be edited? Please help, thank!