Hi all.
There are some successes.

All that remains is to combine the factory and donor calibrations.

 

On 29/11/2024 at 13:53, T_Ivan said:

Xin chào mọi người.
Đã có một số thành công.

Việc còn lại là kết hợp hiệu chuẩn của nhà máy và nhà tài trợ.

 

 

Try it

BCM_K9_OPEL_MOKKA_2013_STOK.zip

6 hours ago, Rain said:

Try it

Thank you.
I'll try it today and give feedback.

I learned how to activate menu items such as:
1. Heated seats during auto start
2. Cooling of seats during autostart
3. Lost key control
4. Remote start

 

Menu items are in calibration No. 2

 

13 hours ago, Rain said:

Try it

It didn't work (((

 

 

 

16 hours ago, T_Ivan said:

Nó không có tác dụng (((

 

 

 

 

 

 

 

 

 

This is the display part so it doesn't matter for remote start. I compared your file with mine and found which BIT to modify and enable it. maybe I will review it and send it back to you later. if you press start on the key, the turn signal flashes twice but the engine only makes a relay click, then you need to change it on the ECM file. Same with my car if only BCM is changed. I changed ECM too for remote start to work

24 minutes ago, Rain said:

This is the display part so it doesn't matter for remote start. I compared your file with mine and found which BIT to modify and enable it. maybe I will review it and send it back to you later. if you press start on the key, the turn signal flashes twice but the engine only makes a relay click, then you need to change it on the ECM file. Same with my car if only BCM is changed. I changed ECM too for remote start to work

At EMC they changed everything for me when they did the Euro 2 firmware.
When I press start, the car blinks the turn signals twice and nothing else happens.

On 11/13/2024 at 11:41 PM, zamich85 said:

When I press the start button, the car only blinks twice.

Should I send you a DPS archive of native calibrations or a read bin file from ECM?
Or send you the file that I uploaded to ECM?

1 hour ago, Rain said:

I compared your file with mine and found which BIT to modify and enable it

I have calibrations #5 and #10 from encore.
It has autostart from the factory, what should I pay attention to when comparing?

19 hours ago, T_Ivan said:

Should I send you a DPS archive of native calibrations or a read bin file from ECM?
Or send you the file that I uploaded to ECM?

ok. Send me a read bin file from ECM and original ECM file. Remote start use calibrations #5 and #10

13 hours ago, Rain said:

ok. Send me a read bin file from ECM and original ECM file. Remote start use calibrations #5 and #10

ECM.zip

 

ECM:

1. STOK = Original - bin

2. TUN = Modified - bin

3. K20_ECM_STOK = ECM SPS calibrations

 

BCM FROM BUICK ENCORE 2014 WITH AUTO START:

1. Calibration #5

2. Calibration #10 

BCM_KL4CJDSB4DB098308.zip

12 hours ago, T_Ivan said:

use calibrations #5 and #10

It won't work (not programmable) with your calibrations 5 and 10.

5_95269311

10_95130349

 

3 hours ago, T_Ivan said:

10_95130349

The problem is in calibration No. 10, because of it it cannot be flashed. @Rain

18 hours ago, T_Ivan said:

Vấn đề nằm ở hiệu chuẩn số 10, vì thế không thể flash được. @Rain

yes i have added 1 paragraph to file number 10 and maybe it can not flash

1 minute ago, Rain said:

yes i have added 1 paragraph to file number 10 and maybe it can not flash

I couldn't flash with your file #10.

52 minutes ago, T_Ivan said:

Tôi không thể flash file số 10 của bạn được.

On your file number 5 I can't find the bit to turn on BTV. 

This piece of code

57 minutes ago, T_Ivan said:

Tôi không thể flash file số 10 của bạn được.

File number 10 is used to fix the problem of the hood latch and remote

1 hour ago, Rain said:

On your file number 5 I can't find the bit to turn on BTV. 

This piece of code

I checked the following files:

1. 95269311

2. 95130531

3. 95130909

4. 95130536
there is nothing similar.

 

all these calibrations are from cars with autostart, except #1 (stok).

1 hour ago, Rain said:

File number 10 is used to fix the problem of the hood latch and remote

what needs to be changed in source file #10?

On 1/13/2025 at 3:54 PM, T_Ivan said:

what needs to be changed in source file #10?

 

 

Try it and then run GDS2 to scan for errors.

 

BCM_K9_OPEL_MOKKA_2013_STOK.zip

On 1/16/2025 at 10:10 AM, Rain said:

Try it and then run GDS2 to scan for errors.

It didn't work.

28 minutes ago, T_Ivan said:

Nó không có tác dụng.

Can't flash or what error does it give when you scan for errors with GDS2?

8 minutes ago, Rain said:

Can't flash or what error does it give when you scan for errors with GDS2?

There are no errors in the control units.
Programmable without problems.

 

Startup does not occur.

 

The only thing I noticed was that before, when the car was armed, the red indicator was constantly on, but now it began to blink.

16 hours ago, T_Ivan said:

Không có lỗi trong các đơn vị điều khiển.
Có thể lập trình mà không có vấn đề gì.

 

Không xảy ra hiện tượng khởi động.

 

Điều duy nhất tôi nhận thấy là trước đây, khi xe được kích hoạt, đèn báo màu đỏ liên tục sáng, nhưng bây giờ nó bắt đầu nhấp nháy.

Can you take a video of what happens when you start the car remotely? What is the flashing red light?

16 hours ago, T_Ivan said:

Không có lỗi trong các đơn vị điều khiển.
Có thể lập trình mà không có vấn đề gì.

 

Không xảy ra hiện tượng khởi động.

 

Điều duy nhất tôi nhận thấy là trước đây, khi xe được kích hoạt, đèn báo màu đỏ liên tục sáng, nhưng bây giờ nó bắt đầu nhấp nháy.

Like mine would be like this but the car won't start. Needs additional ECM intervention

3 hours ago, Rain said:

Needs additional ECM intervention

I downloaded the data from the ECM again to make sure everything was recorded correctly. 

Everything is fine in ECM.