Changing the VIN in GM SMD AirBag modules is vital when recycling a used module. You can achieve this by using this DPS file.

These files only works with GM Global-A vehicles.

 

Play the video to see the process.

https://cameraloops.ru/uploads/videos/sdm_vin_change.mp4

 

GM Global-A 2 byte seed file 

 

 

GM Global-A 5 byte seed file 

View full gm info

This procedure can be done by GMLAN, on bench?

19 hours ago, Lister Llanes said:

This procedure can be done by GMLAN, on bench?

 

Yes it can.

Will it work on a 2010 Chevrolet Cruze? i've changed the module to a used one and it has the VIN of the old car. BCM cannot comm with it.

Just now, Selektion Automotive said:

Will it work on a 2010 Chevrolet Cruze? i've changed the module to a used one and it has the VIN of the old car. BCM cannot comm with it.

 

Yes, it will change the VIN.

14 hours ago, Troy said:

 

Yes, it will change the VIN.

Do you know if it's a 2 or 5 byte seed?

2010 is 2 byte seed. 

Do you know it i can read SDM on bench with scanmatik to make this exchange? If so were can i get the pinout?

I'm not getting comm with the modulo. DPS closes suddendly and SPS gives error of comm

1 hour ago, Selektion Automotive said:

Do you know it i can read SDM on bench with scanmatik to make this exchange? If so were can i get the pinout?

I'm not getting comm with the modulo. DPS closes suddendly and SPS gives error of comm

sdm uses low speed can bus

 

with 4 cables in the small connector, you can communicte with SDM in DPS

 

9 0.5 RD/WH 4440 Battery Positive Voltage

15 0.35 D-GN 5060 Low Speed GMLAN Serial Data

17 0.35 PK 1139 Ignition 1 Voltage

19 0.5 BK/WH 2751 Ground

thnaks for the help. Will try it later.

 

1 hour ago, Arbe_gtc said:

sdm uses low speed can bus

 

with 4 cables in the small connector, you can communicte with SDM in DPS

 

9 0.5 RD/WH 4440 Battery Positive Voltage

15 0.35 D-GN 5060 Low Speed GMLAN Serial Data

17 0.35 PK 1139 Ignition 1 Voltage

19 0.5 BK/WH 2751 Ground

Same. 
Try to program it and DSP crashes. 

2 hours ago, Selektion Automotive said:

Same. 
Try to program it and DSP crashes. 

U have dll problem. Find these from @Arbe_gtc and try it. 

What did you found? 

I dont think its a DLL problem. It also happens with SPS, i've no comms with SDM

are you using globaltis (offline) or tis2web.service.opel.com (online)?

Not sure, but may be SDM have wake up signal. Have to be checked

27 minutes ago, Arbe_gtc said:

are you using globaltis (offline) or tis2web.service.opel.com (online)?

@Arbe_gtc tis2web.service.opel.com

 

@Lyubomir Krastanov no, i think you maybe right it might be .dll or something like this. I can't programm any module. Every time i try, DPS crashes 

delete the navivelibs folder

 

C:\Users\%username%\sps\nativelibs

 

when you launch SPS, it downoads again.

and try again

bear in mind I just check wiring diagrams and there is show obd-ipc-sdm, so to communicate with sdm may require to have ipc in line. As well you can try to go in GDS2 and configure SDM from there have option for new module. Someone on Insignia this rewrite VIN

 

33 minutes ago, Lyubomir Krastanov said:

bear in mind I just check wiring diagrams and there is show obd-ipc-sdm, so to communicate with sdm may require to have ipc in line. As well you can try to go in GDS2 and configure SDM from there have option for new module. Someone on Insignia this rewrite VIN

 

 

@Lyubomir Krastanov i don't have GDS2

37 minutes ago, Arbe_gtc said:

delete the navivelibs folder

 

C:\Users\%username%\sps\nativelibs

 

when you launch SPS, it downoads again.

and try again

@Arbe_gtcdidn't work. 
Gives a Error E4399 

download and install it

18 minutes ago, Lyubomir Krastanov said:

download and install it

 

Do you have a link where i can donwload a fully working version?

 

12 hours ago, Lyubomir Krastanov said:

bear in mind I just check wiring diagrams and there is show obd-ipc-sdm, so to communicate with sdm may require to have ipc in line. As well you can try to go in GDS2 and configure SDM from there have option for new module. Someone on Insignia this rewrite VIN

 

this works fine:

 

 

 

 

@Arbe_gtc that I say may be as not check wiring diagrams and no have SDM module yet.

@Arbe_gtc 2 questions..

 

Can you show how you made the connections in Red and Blue circles?
 

"17 0.35 PK 1139 Ignition 1 Voltage"

When you say this connection is it a normal 12v connection?