4 minutes ago, ZmanCamaro said:

Here's a pic

You have the key on and it's plugged into the OBD2 port?  It didn't receive anything back from the vehicle.

U have to populate VIN

Just now, codebuilder said:

You have the key on and it's plugged into the OBD2 port?  It didn't receive anything back from the vehicle.

This does not use a key it's push button start, but yes it's in the Acc mode correct?

Just now, ZmanCamaro said:

This does not use a key it's push button start, but yes it's in the Acc mode correct?

Yeah, maybe try full ignition on (engine off).  I've just tested the file I've made for you, it should look similar to below:

 

1 minute ago, Lyubomir Krastanov said:

U have to populate VIN

No the HMI was a used and codebuilder is thinking the Vin file you get me could fix this or need Troy HMI Vin program is that what you are thinking?

Thanks for testing that maybe a Lic could be my issue? I am uninstalling and then reinstall and try... 

11 minutes ago, ZmanCamaro said:

Here's a pic

Something is definitely strange.  I purposely unplugged my OBD2 connection and I get further than you.  I don't see that Disable HS-CAN...

 

 

4 minutes ago, ZmanCamaro said:

Thanks for testing that maybe a Lic could be my issue? I am uninstalling and then reinstall and try... 

Also, maybe try the 4.46 version, I had issues with something on 4.48 before

Yeah I think I know, in your pic the Protocal you set to xvdiag, in my pull down it's not there, but not sure why no vxdiag I even have it running? Sure something i'm doing wrong?

I use 4.52, but if you want drop me PM and will help you remotely

Yeah I on'y have 4.48 now. Also I am not getting the VXdiag like you do, so I am being asked by DPS 4.48 MDI or MDI2 so I should or need to get VXDiag choosen?

 

But VXDiag works?

5 minutes ago, ZmanCamaro said:

Yeah I think I know, in your pic the Protocal you set to xvdiag, in my pull down it's not there, but not sure why no vxdiag I even have it running? Sure something i'm doing wrong?

Ohhhhhhhhh, yes, you don't have the VX Diag installed properly.  Make sure you pick Pass-through when installing it.  I have never been able to use "MDI" with my VCX Nano, at least not for a few years.

How do I get VXDiag installed so DPS 4.48 so I can choose it as in codebuilder it's listed? This is the first issue I think?

Just now, codebuilder said:

Ohhhhhhhhh, yes, you don't have the VX Diag installed properly.  Make sure you pick Pass-through when installing it.  I have never been able to use "MDI" with my VCX Nano, at least not for a few years.

Will reinstall now...

1 minute ago, ZmanCamaro said:

Will reinstall now...

I picked GM one DOH.....

Well that did not work by just  reinstalling and then picking Pass Thru... Now uninstalled and reboot and try again...

 

WE HAVE some JOY!!!! it's working....

3 minutes ago, ZmanCamaro said:

WE HAVE some JOY!!!! it's working....

Yeah, the VCX install options can be a bit confusing 🙂

Well it's programmed fully but still have Theft Locked. So I will purchased the Troys GM HMI and maybe I will get it in a few hours as Troy shows away...

Ok thank you codebuilder and Lyubomir Krastanoy!!  So I will need this program, just want to confirm?  Troy's  "GM USA Satellite Radio And HMI 2.5, HMI 2.0 Module VIN Number Relearn DPS File" I don't think I need Video in motion?

 

Thank you again, I'm getting so close with all your help...

 

Christopher

11 minutes ago, ZmanCamaro said:

Ok thank you codebuilder and Lyubomir Krastanoy!!  So I will need this program, just want to confirm?  Troy's  "GM USA Satellite Radio And HMI 2.5, HMI 2.0 Module VIN Number Relearn DPS File" I don't think I need Video in motion?

 

Thank you again, I'm getting so close with all your help...

 

Christopher

That's correct, that's the only file you need.  The calibrations I gave you, I actually put video in motion, typing allowed, etc in for you.

Wow thank you! does this codebuilder upgrade let me watch videos while driving...LOL

 

Thank you so much ok going to purchase that program, I think it's a Cal file and I do the same as your file method? As when I was in DSP I clicked and looks like I can add a VIn and maybe not save without a Cal file and this is what's $100? 

 

Thank everyone again for the help!!

Christopher

 

11 minutes ago, ZmanCamaro said:

Wow thank you! does this codebuilder upgrade let me watch videos while driving...LOL

 

Thank you so much ok going to purchase that program, I think it's a Cal file and I do the same as your file method? As when I was in DSP I clicked and looks like I can add a VIn and maybe not save without a Cal file and this is what's $100? 

 

Thank everyone again for the help!!

Christopher

 

lol it does, just don't get a distracted driving ticket 😛

 

I haven't used Troy's (I have my own applications) but I watched the video and it looks like it's made as a DPS archive as well.  He has a comment there too, you get the file right away even though Troy isn't around right now.

Just got the download, that was fast now going to do it with the video...

 

I will post back in a few...

Not sure what I did wrong I choose 1 (33.3KBd) and opened it as I downloaded from a Mac and copied it to a thumb drive and now opened DSP Select Cal that file and get could not unzip file? 

 

No Joy yet... Any suggestions? I will re-down load it